|
 Protech
Bearing Isolators
Supplier:
JM Clipper
The
Protech design provides unmatched two-way sealing to
prevent premature bearing failure. These bearing isolators
are made of PTFE with a unitized, two-piece construction,
and are reliable even in the most extreme environments.
| • |
Unitized,
two-piece, non-contact design |
| • |
Zero
lubricant leakage |
| • |
Total
exclusion of contaminants |
| • |
Extended
bearing life |
| • |
Exceed
IEEE-841 for electric motors |
| • |
Patented
and additional patents pending |
| Technical
Specifications |
| • |
Total
Eccentricity: .020" TIR (0.51mm) |
| • |
Shaft
Speed: Up to 5,000 fpm |
| • |
Pressure:
0 psi |
| • |
Temperature
Range: -40° to 250° F (-40° to 121°
C) (Standard Materials) |
| • |
Chamfer
Width — CHa: .032" to .063" (0.81mm
to 1.6mm) |
| • |
Bore
Width — CHb: .032" to .063" (0.81mm
to 1.6mm) |
| • |
Compatibility:
Compatible with most bore and shaft materials |
| Protech
Bearing Isolators are available in all of these
materials: |
| • |
Graphite-reinforced
PTFE |
| • |
Mineral-reinforced
PTFE |
| • |
Stainless
steel-reinforced PTFE |
| • |
Bronze-reinforced
PTFE |
| • |
New
high-temperature and large-diameter reinforced PTFE |
|
|
MICRO-TEC™
Bearing Protector Seals
Supplier: Garlock
Available
in both standard and custom designs, MICRO-TEC Seals
excel in sealing all rotating equipment commonly found
in harsh environments, such as coal and mineral mines,
pulp and paper mills, petrochemical plants, construction
sites and steel and aluminum mills.
| • |
Rotor
O-rings eliminate frictional heat and shaft wear |
| • |
Design
allows for up to .060" (1.524mm) total misalignment
and runout typical on difficult applications |
| • |
Standard
seals handle temperatures from -40° F to 400°
F (-40° C to 205° C) and resist most chemicals |
| • |
Non-contact
design minimizes heat buildup |
| • |
No
drag on equipment, and very little torque required |
| • |
Unitized
construction for easy installation |
| • |
Self-sealing
and self-lubricating |
|
|
Series
CBS Bearing Protector
Supplier: PPC Mechanical Seals
This
mechanical seal provides positive sealing in horizontal
or vertical applications. It can be used to close off
the bearing housing vent to eliminate atmospheric aspiration.
| • |
Runs
in flooded and semi-flooded conditions |
| • |
Cartridge
design allows quick, easy installation |
| • |
Fits
most bearing housings without modification |
| • |
Positive
drive |
| • |
Pressure
capability to 15 psi |
| • |
Will
not wear or fret shaft |
|
|
 Permanent
Bearing Protector
Supplier: Inpro/Seal
Company
This
bearing isolator will provide the highest level
of bearing protection available.
| • |
Made
of high-quality bronze, designed to last for
at least 1,000 hours |
| • |
Rotor
and stator form a non-contact, compound labryinth
– there is nothing to wear
out |
| • |
Damaged
shafts do not need to be repaired in order
to retrofit this bearing isolator |
| • |
Split
seal for large shafts, simplifying installation |
| • |
Can
be manufactured and shipped in 24 hours, if
needed |
| • |
Many
popular pump applications are stock |
|
|
AquaGard™
System
Supplier:
JM Clipper
The
AquaGard System protects equipment against water damage.
It incorporates two easy-to-install components that
work together to prevent costly maintenance, lubricant
loss and downtime.
AquaChek™
Active Warning System — provides advance notice
of unsafe moisture levels
| • |
Combines
a high-quality bearing isolator and a moisture-alert
sensor |
| • |
Components
are designed for rotating equipment |
| • |
Contact-design
seal works in any orientation, including vertical
down, with zero lubricant leakage or moisture intrusion |
| • |
Green
operational light signals at 10-second intervals
to ensure system is functional |
| • |
Light
flashes yellow when Saturated Relative Humidity
(SRH) levels exceed 70% |
| • |
Sensor
is powered by a 3-year battery |
| • |
Used
in pulp and paper, chemical and petrochemical plants |
|
|
 AquaDri™
Active Moisture Maintenance system —
removes excess moisture and helps extend life of bearings
and lubrication
| • |
Pairs
high-quality bearing isolator with moisture-removing
dryer |
| • |
Complete
system effectively excludes dust and moisture |
| • |
Closed-system
dryer prevents contaminations and spillage |
| • |
Constant-level
dryer does not require any adjustment or level setting |
| • |
Viewport
eliminates the need for separate installation |
| • |
Used
in rotating equipment in pulp and paper, utility,
chemical processing and power generation |
|
| |
|
|
|
| |
|
| |
| CONTACT
US |
| 24-Hour
Emergency Service: 1-800-356-0061 |
Email: infohnsonpackings.com |
| Headquarters:
|
21 Deer
Park Drive, P.O. Box 545, East Longmeadow, MA 01028 | 413-525-5555
| Fax: 413-525-5520 |
| Branch
Office: |
1185 Hammond
Street, Unit 4, Bangor, ME 04401 | 207-262-7110 | Fax: 207-262-7118 |
|
|
